The MAXIMATOR air drive concept provides a number of benefits to you:
MAXIMATOR provides competent consultancy, engineering design and supply of complete systems to optimally and economically solve your testing tasks and offers you extensive Services.
MAXIMATOR Pumps are available in 5 sizes: M, S, G, GX, DPD. The sizes vary according to their suitability for different pumping media, wide ranging flow rates and their maximum allowable operating pressures. MAXIMATOR provides the best-suited fluid pump for each application.
Assembly Instruction MAXIMATOR High-Pressure Pumps
Assembly Instruction MAXIMATOR High-Pressure Pumps Language: English Release: 11/2011
MAXIMATOR pumps can, in principle, be installed in any position, but a maximum service life of the seals is achieved in a vertical one.
Port sizes Important!
Please observe that only screws and tubing are fitted that are suitable for the pressure range of the pump. To ensure an optimum operation (pressure and flow) of the pumps, the port sizes of the pumps shall not be reduced.
The air drive connection is located at the spool valve housing. A second air drive connection as unregulated pilot port on S...D and G(SF) series that has to be connected too, not only provides better pressure control but is also the ideal place to install control instrumentation because of its small size. In any event a compressed air filter and water separator has to be fitted to the pump. Filters with water separator, pressure regulator, control pressure gauge and shut-off valve are optionally available under ”Air control unit C....“, depending on the pump line.
No air lubricator is required since the pump received Barium grease treatment. Has a lubricator been used once, it is strongly recommended to continue. If there is only very dry air available, an air lubricator is needed.
are in general between –20°C to +80°C (standard). The pumps with –VE seal version can be operated up to max. +60°C, at short term up to +80° would be acceptable. For outdoor service at temperatures of 0°C and below, special versions are available on request.
Proper operation and efficiency of the pumps is mainly depending on the quality of the used hydaulic liquid. We recommend hydraulic oils with a viscosity between 46 – 68 cst, i. e. Manufacturer Hydraulic oil to DIN 51524 T2; DIN 51519; ISO VG 46
|ARAL||VITAM GF 46|
|BP||ENERGOL HLP 46|
|ESSO||NUTO H 46|
|SHELL||TELLUS Oil 46|
|HYDROL DO 46|
|HYDROL HV 46|
|DEA||ASTRON HLP 46|
The drive air should have a quality class of 3 to 4 (solids/water/oil) according to the recommendation no. 611/1984 by PNEUROP (European Committee of Manufacturers of boosters, vacuum pumps and air driven tools).
Please note that by using humid air of high humidity in continuous operation the problem of icing could occur. We suggest to install a water seperator and a dryer in the drive air line. If the drive air is too dry and has got a dew point lower than - 40°C, we suggest to use an oiler. By observing this drive air quality, an optimum life time of the seals and packings will be achieved.
MAXIMATOR pumps are suitable for liquid applications. To select and order a hydraulic pump that is suitable the best for your applications, the following parameters have to be observed:
1. Liquid to be handled
The type of liquid is essential to select a MAXIMATOR pump hence the wetted material of construction and compound of the seals are determined by the specific fluid. MAXIMATOR pumps are available for several services. The two most important we are offering standard pumps are for oil or water use, see also ordering codes.
2. Available Air Drive pressure
MAXIMATOR pumps are designed for an air drive pressure of pL = 1 to 10 bar (14,5 to 145 psi) maximum.
3. Required hydraulic outlet pressure and flow capacity
The outlet pressures given in the technical pump tables are based upon a maximum air drive pressure of pL = 10 bar. The real oulet pressure in your specific case is determined by air drive pressure multiplied by pressure ratio, pL * i. The indicated flow capacities Qmax is the maximum value which can be reached at an outlet pressure of 0 bar and an air drive of pL = 6 bar. The real flow capacities at a specified outlet pressure are listed in the flow charts, page 20 to 23.